opendmarc

NAME
SYNOPSIS
DESCRIPTION
OPTIONS
SIGNALS
VERSION
COPYRIGHT
SEE ALSO

NAME

opendmarc − DMARC email policy filter for MTAs

SYNOPSIS

opendmarc [−A] [−c configfile] [−f] [−l] [−n] [−p socketspec] [−P pidfile] [−t file[,file[...]]] [−u userid[:group]] [−v] [−V]

DESCRIPTION

opendmarc implements the proposed DMARC specification for authentication of message and reporting of observed traffic.

opendmarc uses the milter interface, originally distributed as part of version 8.11 of sendmail(8), to provide a DMARC processing service for mail transiting a milter-aware MTA.

Most, if not all, of the command line options listed below can also be set using a configuration file. See the −c option for details.

opendmarc relies on addition of Authentication-Results fields by upsteam filters on trusted hosts to collect input to the DMARC algorithm. It does not itself do DKIM or SPF evaluation.

OPTIONS

−A

Automatically re-start on failures. Use with caution; if the filter fails instantly after it starts, this can cause a tight fork(2) loop. This can be mitigated using some values in the configuration file to limit restarting. See opendmarc.conf(5).

−c configfile

Read the named configuration file. See the opendmarc.conf(5) man page for details. Values in the configuration file are overridden when their equivalents are provided on the command line until a configuration reload occurs. The OPERATION section describes how reloads are triggered. The default is to read a configuration file from @SYSCONFDIR@/opendmarc.conf if one exists, or otherwise to apply defaults to all values.

−f

Normally opendmarc forks and exits immediately, leaving the service running in the background. This flag suppresses that behaviour so that it runs in the foreground.

−l

Log via calls to syslog(3) any interesting activity.

−n

Parse the configuration file and command line arguments, reporting any errors found, and then exit. The exit value will be 0 if the filter would start up without complaint, or non-zero otherwise.

−p socketspec

Specifies the socket that should be established by the filter to receive connections from sendmail(8) in order to provide service. socketspec is in one of two forms: local:path which creates a UNIX domain socket at the specified path, or inet:port[@host] or inet6:port[@host] which creates a TCP socket on the specified port within the specified protocol family. If the host is not given as either a hostname or an IP address, the socket will be listening on all interfaces. If neither socket type is specified, local is assumed, meaning the parameter is interpreted as a path at which the socket should be created. If an IP address is used, it must be enclosed in square brackets. This parameter is mandatory.

−P pidfile

Specifies a file into which the filter should write its process ID at startup.

−t file[,file[,...]]

Reads email messages from the named files and processes them as if they were received by the filter. The service is not started, and actions normally sent back to the MTA will instead be printed on standard output.

−u userid[:group]

Attempts to be come the specified userid before starting operations. The process will be assigned all of the groups and primary group ID of the named userid unless an alternate group is specified. See the FILE PERMISSIONS section for more information.

−v

Increase verbose output during test mode (see −t above). May be specified more than once to request increasing amounts of output.

−V

Print the version number and supported canonicalization and signature algorithms, and then exit without doing anything else.

SIGNALS

Upon receiving SIGUSR1, if the filter was started with a configuration file, it will be re-read and the new values used. Note that any command line overrides provided at startup time will be lost when this is done. Also, the following configuration file values (and their corresponding command line items, if any) are not reloaded through this process: AutoRestart (−A), AutoRestartCount, AutoRestartRate, Background, MilterDebug, PidFile (−P), Socket (−p), UMask, UserID (−u). The filter does not automatically check the configuration file for changes and reload.

VERSION

This man page covers version @VERSION@ of opendmarc.

COPYRIGHT

Copyright (c) 2012, The Trusted Domain Project. All rights reserved.

SEE ALSO

opendmarc.conf(5), sendmail(8)

Sendmail Operations Guide

RFC4408 − Sender Policy Framework

RFC5321 − Simple Mail Transfer Protocol

RFC5322 − Internet Messages

RFC5451 − Message Header Field for Indicating Message Authentication Status

RFC6376 − DomainKeys Identified Mail

RFC6591 − Authentication Failure Reporting Using the Abuse Reporting Format